Model |
Type |
|
Mainframe |
|
Blank Module |
|
Programmable Digital Multi-meter |
|
L-C Meter |
|
Universal Counter |
|
Function Generator |
|
Triple Power Supply |
|
|
 |
- Base unit for insert modules from the 8000 series modular
system
- Power supply for two modules
- DC voltages electronically
regulated, non-grounded and short-circuit-proof
- Up to 5 base units
can be stacked
- Insert module for separate circuits available
- 4
BNC connectors on the rear panel of the HM8001-2 (Option HO801) provide
for signal transmission to and from HM8018, HM8021 and HM8030-6 modules |
|
 |
- Insert module for customized instrument construction
-
Guide rails for mounting circuit boards at 4 different levels
- Plastic
front panel for easy processing
- Power is supplied by the basic unit
HM8001-2
- Available supply voltages (max. 18 W):
2 x 8
VAC / 0.5 A
2 x 5 VDC / 1 A
4 x 20 VDC / 0.5
A
- Basic unit HM8001-2 required for operation |
|
 |
- 4 ¾ - digit display with 50,000 counts, basic
accuracy 0.05%
- Automatic and manual range selection
- Max
resolution 10 μV, 0.01 dBm, 10 mA, 10 mΩ, 0.1° C/°F
- Offset function /
relative value measurement in basic measurement functions
-
Input impedance > 1 GΩ (0.5 V and 5 V DC range)
- RS-2323
interface
- PC software for control and data logging
- Basic unit
HM8001-2 required for operation |
|
 |
- Frequency range: 0 Hz ~ 1.6 GHz
- 10 MHz
time basis with o.5 ppm stability (TCXO)
- Input A :
Input impedance 1 MΩ, maximum sensitivity 20 mVrms
-
Input B :
Input impedance 50 MΩ, maximum
sensitivity 30 mVrms
- Time interval resolution up to 10 ps
- Offset
mode over the entire measurement range
- Gate input (in combination
with HO801)
- Basic unit HM8001-2 required for operation |
|
 |
- Frequency range: 50 mHz ~ 10 MHz
- High
signal purity and amplitude stability
- Output voltage: 20Vpp (10 Vpp
to 50Ω)
- Surge- and short-circuit-proof output
- Distortion factor
< 0.5% up to 100 kHz
- Internal and external sweep
- Pulse width
adjustment
- Highly accurate digital frequency display
- Basic unit
HM8001-2 required for operation |
|
 |
- Measurement functions: L, C, R
-
3 ½ - digit display with 2,000 counts, basic accuracy 0.5%
- 4-wire
measurement
- Max. resolution: 0.1 pF, 0.1 μH, 10 mΩ, 0.01 μS
-
Internal bias for electrolytic capacitors connectable
- Offset
adjustment of cable capacity for the “Kelvin test lead”
- AC voltage
signal proportional to value shown in the display
to rear
panel BNC connector (with Option HM801 only)
- Basic unit HM8001-2
required for operation |
 |
HM8040-3(Triple Power Supply
Unit) |
|
 |
- 2x 0~20 V / 0.5 A, 5 V / 1 A
- 3-digit
display, separate for current and voltage
- Display resolution 0.1V /
1mA
- Adjustable current limiter
- Electronic fuse
- Linear
series regulator
- Low residual ripple and low noise
- Out put
ON/OFF key
- Basic unit HM8001-2 required for operation |
| |
))
